Toy11 VT4C 211AMP -1

Start to prepare the component and box.


Estimate the placement for good signal and easy hand make.



Estimate placement picture.

ToyX project EQ Linearizer study case3

Tuning each inductor value for meet LC band pass filter.


Finish each band pass  structure.


Test each band the frequency of drift .


Side view picture.

Estimate EQ  Linearizer outline and prepare drawing  of  EQ case.

Turntable test machine

All testing utility

VCO arm of pick up.

Detect pin1 & rotate VCO.

VCO RF test head.

VCO arm pick off.

Put  VCO in tub of  roller.

Detect sensor.

VCO test handle.

ToyX project EQ Linearizer study case2

Placement Band pass filter.


Solder capacitor of band pass filter.


Estimate placement.

EQ Linearizer  will be mono mono stack by two layer.

Recall1 DVB-T diy

DVB-T platform build in Cheertek main chip with transcoder and could receive DVB-T tuner signal then transfer into Video,Audio signal same time.
DVB-T got remote control ability through UR interface.


Platform rear view.



RF tuner zoom in picture.
DVB-T tuner use Quantel receiver and Afa9003 transcoder.

Diy8 DAB receivre

DAB tuner Hitachi receiver & SAW build in  support VHF Band-III & L-Band (1.5GHz)

Baseband Ti32C5416 DSP with bus bridge connect USB controller.
Could play DAB audio and send DLS（Dynamic Label Segments）through USB same time.

DAB tuner mount on baseband platform.
DAB box inner connection with power module and audio connector.
.

ToyX project EQ Linearizer study case1

I design a DIY EQ Linearizer call X project.
Simulate the band filter for to correct phase shift issue.
The 5 band pass CF will be 50Hz,250Hz,1KHz,4KHz,12.8KHz.

50Hz first band in band1
Band1: 5~100Hz(5 pcs 20hz band pass filter inside 5~20,20~40,,80~100hz)
橫跨頻寬20Hz 中央是相位0度,左-Pi 是-180度 & 右+Pi是 +180度相位 .

Use other program to verify L-C frequency.

250Hz first band in band2
band2:250Hz (5 pcs 60hz band pass filter inside 100~160,160~220,,340~400hz)
橫跨頻寬60Hz 中央是相位0度,左-Pi 是-180度 & 右+Pi是 +180度相位 .

1KHz first band in band3
band3:1KHz (5 pcs 240hz band pass filter inside 400~640,640~880,,1360~1600Hz..)
橫跨頻寬240Hz 中央是相位0度,左-Pi 是-180度 & 右+Pi是 +180度相位 .

4KHz first band in band4
band4:4KHz (5 pcs 1Khz band pass filter inside  1.6K~2.56K,2.56k~3.56k,,5.4K~6.4KHz)
橫跨頻寬1KHz 中央是相位0度,左-Pi 是-180度 & 右+Pi是 +180度相位 .

12.8KHz first band in  band5
band:12.8KHz(5 pcs 2.56K band pass filter inside 6.4K~ 9.86K,9.86k~11.52K,,16.64k~19.2Kband...)
橫跨頻寬2.56KHz 中央是相位0度,左-Pi 是-180度 & 右+Pi是 +180度相位 .

由此可知........
低頻橫跨頻寬20Hz 中央是相位0度,左右差10Hz 分頻器相差就達到180度相位 誤差.
低頻分頻器相差 ,造成訊號失真大,破壞音質,而不只是分頻器相差, 造成時間差而已 .
低頻分頻器相差 ,造成訊號失真, 聲音就易糊成一團 ,低頻彈跳感減弱.

.........................不知數位及DSP 等化器要如何補, 如何調?