Grid Tied Inverter
Power facter about 0.87 @165W
2013年1月10日 星期四
2013年1月4日 星期五
中音路- 離子高音 Plasma Tweeter of 2.1 channel ...the END!
Finish!
羅老 sorry 轉貼 Look-T blog...
點火....一道紫色光噴出，送上音樂一陣奇妙的聲音在耳邊響起，調好音壓比例，哇.....小提琴的嚓弦聲絲絲入扣，整個音場空氣感十足，這才算是超高音，以我的經驗所有有型體的喇叭發出的氣聲，音質和擴散性真實感都跟不上離子高音，真實感尤其重要，我們多數的音響都只能說好聽，認真說來就缺這種如臨現場的真實感！
另羅老 全新架構300B SE
羅老........十年對管機和輸出變壓器的浸盈研究 ...... 的感性論述.
這新架構的機器背景特別乾淨，一開始有點尖銳，開機一兩小時就相當好聽，現在5分鐘我就感覺到位了，所有的樂器像是跳出來似的，非常的透明立體，單端管機的霧霧感都沒了，再說這樣的霧霧感覺可是花了10年才解決，這也是這機器最大特色。
敝人覺得.....對管機有鐘愛的同好, 一輩子對聲音尋尋覓覓的朋友, 別忘了這個...有可能一解您的宿願.
2012年12月25日 星期二
中音路- 離子高音 Plasma Tweeter of 2.1 channel ...5
Finish 6C45Pi & IF circuit connection and check working bias voltage.
Top view under real testing.
Final check cross-over switching circuit for prepare feed in S.G. signal.
First time generat plasma flaming (small fire).
Re-modify structure of voice-coil actuator.
Use new voice-coil actuator to light up plasma flaming.
After finish shieding-net and check effect of plasma generat.
Youtube file Mr211 Plasma tweeter
2012年12月3日 星期一
中音路- 離子高音 Plasma Tweeter of 2.1 channel ...4
Set Up a platform for hard disk drive voice-coil actuator
Light up plasma using a hard disk drive voice-coil actuator.
Change 500V high voltage transfer for more energy to light up plasma flaming.
Finish retuning 6JM6,ECL82,6C45Pi plate voltage and bias voltage.
Rear view.
Feed in S.G. signal test plasma tweeter and monitor high voltage.
2012年11月19日 星期一
中音路- 離子高音 Plasma Tweeter of 2.1 channel ...3
Finish internal circuit connection.
Finish bottom platform circuit connection.
Finish 6JM6 platform and Tesla coil install.
Prepare test Tesla coil flame.
Rear view.
Front view. After test high-voltage need modify circuit.
6jm6 tube suitable for plasma amplifier still need for estimate.
2012年11月12日 星期一
中音路- 離子高音 Plasma Tweeter of 2.1 channel ...2
For good shielding reason I put shielding net on rack.
Therefor Alumni plate will contact shielding net well.
Install crossover switch module.
Drill hole for well proper layout of amplifier.
Connect relay DC control wire for crossover switch module.
Set 12V transformer for relay DC control usage.
Mount 4 transformers. 5U4G heater transformer ,chock, 6.3V transformer, crossover transformer.
Finish AC main power switch circuit (include a AC delay-on relay).
Finish AC power and Tube heater circuit prepare for turn-on test.
Real test and check each point voltage.
Finish connect wire of crossover switch module and make a test of mode switch.
This weekend the last schedule.
2012年10月30日 星期二
中音路- 離子高音 Plasma Tweeter of 2.1 channel ...1
Old crossover connection block.
New Plasma Tweeter of 2.1 channel amplifier block.
Design wood rack for Plasma tweeter system and size must small and compact suitable for put on woofer box.
After placement design and finish assembly Layer1 module for Plasma tweeter high voltage circuit and Audio feed- in circuit and generate I-F modulate circuit.
Tube 5U4G,6C45Pi,ECL82,6JM6.
Paint wood racks for good looking.
Assemble and estimate rack design.
Check rack in step by step list.
This Layer module will design for high voltage radiation , like RF power amplifier.
For band 5K~40K audio signal radiation.
Switch relay module could switch mode between Old crossover and New Plasma Tweeter of 2.1 crossover.
訂閱：
文章 (Atom)